paul bishop
  • Male
  • Melb Vic
  • Australia
Share
  • Blog Posts
  • Discussions (31)
  • Events
  • Groups
  • Photos
  • Photo Albums

Paul bishop's Friends

  • Greg_

paul bishop's Discussions

mixer tube for p200

Started on Thursday 0 Replies

wondering if anybody has any info on delorto si 24/24 carb emulsifier tube. Have fitted big box exhaust, and changed main jet to 120 (was 118). Current mixer is BE3, and thinking about going to BE4.…Continue

Carburettor upgrade

Started this discussion. Last reply by paul bishop Feb 14. 4 Replies

Hello all. Has anybody done a carb upgrade using the si 26-26e from GPS imports? Considering making the swap on a P200E from standard si 24-24. There are some carbs around sold as 26mm but are in…Continue

Pinasco clutch gear

Started this discussion. Last reply by paul bishop Aug 9, 2019. 2 Replies

Got a pinasco clutch drive plate/gear with 24 teeth (std is 23) to make gearing a bit higher. Fitted it on to my P200E by just removing clutch (no case split). Has made a bit of a difference in the…Continue

Increasing gear ratio

Started this discussion. Last reply by paul bishop Oct 14, 2019. 4 Replies

Looking to get a few lower rpm on highway travel. Anybody put a 100/90/10 tyre on the back (did it fit) and another option is to use 24 tooth clutch drive gear, to replace original 23 t one. I think…Continue

 

paul bishop's Page

Latest Activity

paul bishop posted a discussion

mixer tube for p200

wondering if anybody has any info on delorto si 24/24 carb emulsifier tube. Have fitted big box exhaust, and changed main jet to 120 (was 118). Current mixer is BE3, and thinking about going to BE4. I believe this will alter low to mid rpm performance. Anyone done this?See More
Thursday
paul bishop replied to paul bishop's discussion Carburettor upgrade
"Yep sounds like a good plan. Thanks Rolf."
Feb 14

MEMBER
Rolf replied to paul bishop's discussion Carburettor upgrade
"I was running the 26.26g on a ported Malossi 166 with a tuned pipe.  I think your next step should be to put something like a SIP road exhaust on. This will give more performance improvement than a bigger carburetor on your setup.  Note…"
Feb 14
paul bishop replied to paul bishop's discussion Carburettor upgrade
"Thank you Rolf. I have put on a pinasco 24t clutch drive which does drop a few rpm at highway speed, and of course on the hills it lacks a bit so thought 26mm carb might help. Yes I figured the opening would have to be ported out a bit. I don't…"
Feb 14

MEMBER
Rolf replied to paul bishop's discussion Carburettor upgrade
"I have a 26.26g which is a good upgrade if you are running a performance barrel and exhaust.  If you do go to the 26mm, the inlet into the crankcase should be opened up to match the larger opening of the carburetor. This involves splitting the…"
Feb 14
paul bishop posted a discussion

Carburettor upgrade

Hello all. Has anybody done a carb upgrade using the si 26-26e from GPS imports? Considering making the swap on a P200E from standard si 24-24. There are some carbs around sold as 26mm but are in fact 24mm. The GPS one is stated as direct fit/swap. Any ideas?? Thanks for any info available.See More
Feb 8
paul bishop replied to paul bishop's discussion Increasing gear ratio
"Yes thanks John. That was the route i went, but with Pinasco part. Worked fine with marginal difference. There is now a slight gear whine on closed throttle over-run is only thing i noticed. Highway ride revs a bit lower, and uphill need to change…"
Oct 14, 2019

Profile Information

Vespa Model(s) you own
P200E

Comment Wall (2 comments)

You need to be a Registered User of Vespa Club of Melbourne to add comments!

Join Vespa Club of Melbourne

At 20:54 on May 3, 2015,
MEMBER
Julie Pond
said…

Hi Paul

Welcome to the site...hope we get to meet you sometime soon.

Cheers Julie

At 19:49 on May 3, 2015,
MEMBER
Greg_
said…

Hi Paul and welcome to the website. Come along to next Sunday's breakfast and talk Vespa.

 
 
 

Registered Users

© 2020   Vespa Club of Melbourne Incorporated in Victoria A005069N   Powered by

Badges  |  Report an Issue  |  Terms of Service